GPB Progressive Grease Distributor 油脂分配器

• 3/4/5/6
• Maximum working pressure: 25MPa
• Minimum starting pressure: 1.4MPa
• Standard displacement per port: 0.08mL/cy~0.56mL/cy
• Applicable lubricant range (at standard temperature): lubricating oil≥N68,grease NIGI 00O ~2
• Working environment temperature: -20°C~+60°C (low temperature grease should be used at low temperature)
• Plunger pair with mechanical cycle indicator Maximum cycle rate: 60cy/min
• Maximum circulation rate of plunger pair: 200cy/min
• Number of working pieces of each group of distributors: 3~10 pieces
• The number of lubrication points available for each group of distributors: 3-20 points
• The optimal diameter and length of the distributor output: ф 6mm long 1.2~3.5m; ф 8mm long 1.5~4.5m
• Body material and coating: galvanized carbon steel surface

GPB series progressive distributor is an oil distributor with advanced design and reasonable structure.The GPB distributor series can be used for high pressure and wide temperature change conditions. It can form a single-line lubrication system with manual,electric and pneumatic pumps,etc. It is suitable for various medium-sized machine tools and plastic machinery equipment,or sub-distribution of large single-line lubrication systems,devices,and ideal products for similar applications. A typical set of GPB distributors consists of a ”first piece”,a ”tail piece” and 3 to 10 working pieces. Typically a set of dispensers provides lubrication for 3 to 20 lubribution points. The working pieces of the GPB distributor are available in various size of displacement (see technical specifications for details). Double oil outlet working piece (after the specifications value of the working piece,use T to indicate double oil outlet),there are two oil outlets,respectively at both ends of the working piece; single oil outlet working piece (in the working piece specification After the value,use S for single oil outlet) There is an oil outlet,which can be at either end of the working piece,and the oil outlet,which can be at either end of the working piece,and the oil outlet at the other end needs to be blocked.Note that for the double oil outlet working piece,any oil outlet cannot be blocked,otherwise the distributor will be damaged and its normal operation will be affected.

• 3/4/5/6
• 最大工作压力：25MPa
• 最低启动压力：1.4MPa
• 每口标准排量：0.08mL/cy~0.56mL/cy
• 适用润滑剂范围（标准温度下）：润滑油≥N68、油脂NIGI 00O~2
• 工作环境温度：-20℃~+60℃（低温时应使用低温油脂）
• 柱塞副配有机械循环指示器 最大循环速率：60cy/min
• 柱塞副最大循环速度：200cy/min •每组分配器工作件数：3~10件
• 每组分配器可提供润滑点数：3-20点
• 分配器输出最佳直径及长度：ф 6mm长1.2~3.5m；ф8mm长1.5~4.5m
• 阀体材质及涂层：碳钢表面镀锌

GPB系列递进式分配器是一种设计先进、结构合理的油分配器，GPB系列分配器可用于高压、宽温度变化工况，可与手动、电动、气动等泵组成单线润滑系统，适用于各种中型机床、塑料机械设备，或大型单线润滑系统的分分配，是装置及类似场合的理想产品。 一套典型的GPB分配器由一个“首件”、一个“尾件”和3至10个工作件组成。通常一套分配器为3至20个润滑点提供润滑。GPB分配器的工作件有各种大小的排量可供选择（详情见技术规格书）。双出油工作件（在工作件规格值后用T表示双出油口），有两个出油口，分别在工作件的两端；单出油工作件（在工作件规格值后用S表示单出油口）有一个出油口，可以位于工作件的任一端，还有一个出油口，可以位于工作件的任一端，另一端的出油口需要被堵塞。注意，对于双出油工作件，任何一个出油口都不能被堵塞，否则会损坏分配器并影响其正常工作。